ICAT International
Ductwork manufacturing and integration
A Casablanca-based manufacturer and distributor operating since 1977. Circular and rectangular ducts, fittings, grilles and diffusers form the network backbone.
HMA · HVAC SOLUTIONS
ICAT INTERNATIONALControl the air,
from ductwork to comfort.
ICAT International, RTEC and HVAC System: ductwork manufacturing, ventilation, air conditioning and air handling. Complementary expertise for hotels, offices, hospitals and industrial sites in Africa.
Three areas of expertise.
One coordinated system.
System performance depends on how equipment, ducts, air distribution and controls work together. HMA supports specification and the preparation of a solution suited to building use, climate conditions and operation.
RTEC
Air conditioning and air handling
Splits, VRF, chillers, heat pumps, air handling units, rooftop and precision units, selected according to loads and the required level of control.
HVAC System
Ventilation and airflow
A ventilation range represented by ICAT in Morocco, matched to fresh-air supply, extraction duties and network characteristics.
Industrial origins
Air treatment expertise developed in Morocco.
Complementary areas
Manufacturing, ventilation and air conditioning.
Ductwork airtightness
Declared classes depend on the duct family and execution.
ICAT · RTEC · HVAC SYSTEM
From the first duct
to indoor air quality.
Select by function to coordinate the installation and support dialogue between the engineering team, installer and operator.
01
Ductwork
Circular and rectangular ducts, fittings and mounting accessories. Airflow, available pressure, airtightness and space guide the selection.
02
Air distribution and comfort
Grilles, slot, swirl, multidirectional and long-throw diffusers. Throw and residual velocity are considered alongside acoustics and occupancy.
03
Cooling and heating
Splits, multisplits, ducted units, cassettes, VRF, chillers and heat pumps for homes, commercial premises and central plant.
04
Air handling units
AHUs, rooftop and terminal units to match temperature control, filtration and air treatment to the application. Energy recovery depends on the selected configuration.
05
Hygiene and filtration
SANIX configurations provide cleanable surfaces, section access, drainage and removable components. Filtration up to HEPA H14 depends on the selected AHU and equipment.
06
Smoke extraction and safety
Fan boxes, fans, roof fans, fire and smoke dampers. Temperature classes, duration, markings and test reports must match the specified product and system.
Practical benefits
for projects and operation.
A coordinated technical chain
Combining ducts, distribution and equipment helps coordinate interfaces. Airflows, pressure losses and sound levels are assessed as a system.
A manufacturing base in Morocco
Local production and regional proximity support project-specific configurations. Availability, shipping and lead times are confirmed for each destination.
Equipment matched to use
From hotel comfort to precision requirements, a broad range supports selection around the actual building profile.
Whole-life cost control
Power input, part-load operation, filter costs, maintenance access and spare parts availability matter alongside the purchase price.
Maintenance planned early
Filter access, removable parts, drainage and cleaning requirements inform the specification and help sustain operation.
Documented compliance
Selection sheets, certificates and test reports should be obtained for the selected products. A cited standard is not certification of the complete installation.
A Casablanca-based manufacturer and distributor operating since 1977. Circular and rectangular ducts, fittings, grilles and diffusers form the network backbone.
RTEC · VRF / DC INVERTER
RTEC RV5: modularity
and demand control.
The supplied presentation describes a DC Inverter VRF range, with heat-recovery configurations, corrosion-protection variants and a photovoltaic-connected version. Selection depends on the series, load assessment and operating conditions.
- 246 kW
- Declared maximum combined capacity
- 80
- Indoor units in certain configurations
- 1,000 m
- Declared total piping length for certain series
These maxima may not be available together. Verify combinations, equivalent lengths, height differences, capacity corrections and temperature limits against the selected model data.
Design for heat.
Plan for moisture and maintenance.
In tropical and equatorial climates, selection goes beyond nominal cooling capacity. HMA helps gather the inputs needed by the engineer and manufacturer to validate equipment.
Heat and latent loads
Assess outdoor temperature, humidity, occupancy and fresh-air loads. Check sensible and latent capacity at design conditions and part-load control.
Condensation and drainage
Specify continuous insulation and suitable vapour control on cold surfaces, accessible drain pans and condensate drainage that can be inspected.
Coastal exposure and dust
Define salt exposure, materials and coatings, filtration and cleaning intervals. Confirm corrosion protection on the proposed model.
Continuity and maintenance
Document power supply, any redundancy, technical access, filter stock and spare parts availability. Plan maintenance at the design stage.
Demanding uses.
References across sectors.
The ICAT presentation supplied to HMA lists the following references. They illustrate sectors served by the manufacturer and are not projects attributed to HMA.
Hospitality
La Mamounia · Four Seasons · Royal Mansour · Sofitel
Commercial and transport
Casablanca, Rabat and Marrakech airports · Morocco Mall · IKEA
Healthcare and pharmaceuticals
University hospitals · Ibn Rochd Hospital · Pfizer · Roche · Sothema
Industry and infrastructure
Siemens · Somaca · Yazaki · Hassan II Mosque · Jorf Lasfar
HMA: from specification
to a well-prepared enquiry.
Define the brief
Country, use, drawings, loads, airflows, acoustic targets and safety requirements.
Prepare the selection
Configurations, design climate conditions, controls, interfaces and required technical documents.
Build the offer
Clarify supply scope, logistics, lead times, commissioning and maintenance with the project team.
HMA × ICAT INTERNATIONAL
Your next project
starts with better air design.
Share your drawings, project country, constraints and programme to prepare a technical enquiry with HMA.
DOCUMENTATION & CREDITS
Based on the HMA ICAT HVAC CVC presentation and official websites consulted on 17 October 2026. Confirm ranges, performance and certification for the products offered. Product visuals and illustrations are extracted from the supplied presentation; trademarks and credits belong to their respective holders.